587 Product Finder MF UNC UNF G Rp, R, Rc NPT, NPTF BSW Pg MJ UNJC, UNJF EG (STI) SELF-LOCK Tr, Tr-F Rd Glatt Smooth GT, TD PoCoSys Kalibrieren Calibration Zubehör Accessories M Kegeliger Gewinde-Rundlauf-Prüfdorn · Tapered Check Plug Gauge for Radial Run-Out M P 60° DIN 13 SW ø d2 ø d1 l1 l2 3xP 1xP A 0,01 A Antastzylinder Contact cylinder Gewinde-Gutlehrdorn, Flankendurchmesser Thread plug gauge go, pitch diameter Gewinde-Ausschusslehrdorn, Flankendurchmesser Thread plug gauge no-go, pitch diameter Zur Prüfung der Gewindelage auf 3D-Messmaschinen und zur Rundlaufprüfung For checking the thread position on 3D measuring machines and radial run-out ø d 1 mm ø d 2 l 1 l 2 SW M 3 2,2 25,5 4,5 2 4 3 30 6 2,5 5 3,5 30 6 3 6 4,5 32 8 4 Auf Anfrage 8 6 34 10 5 10 8 36 12 6 Upon request 12 9 40 16 8 16 12 42 18 10 20 12 42 18 10 Weitere Ausführungen auf Anfrage Further designs upon request Eigenschaften des kegeligen Gewinde-Rundlauf-Prüfdorns: • Rundlaufgenauigkeit des Antastzylinders (ø d2) zum Gewinde-Außendurchmesser (ø d1) kleiner 0,01 mm • Flankendurchmesser des Gewinde-Gutlehrdorns am 3. Gewindegang (3xP) ➞ ausreichende Führung im Gewinde • Flankendurchmesser des Gewinde-Ausschusslehrdorns am vorletzten Gewindegang (l2 – 1xP) ➞ Klemmung des Prüfdorns • Der Gewinde-Außendurchmesser ist zylindrisch auf das Maß des Gewinde-Gut-Lehrdorns gefertigt um zu gewährleisten, dass der Prüfdorn im Flanken- und nicht im Außendurchmesser klemmt Handhabung des kegeligen Gewinde-Rundlauf-Prüfdorns: • Der Prüfdorn wird von Hand bis zum Festsitz in das Innengewinde eingeschraubt • Durch den leichten Formkegel im Flankendurchmesser auf die gesamte Gewindelänge (l2) zentriert sich die Achse des Prüfdorns mit der Achse des Innengewindes • Die Koaxialität des Innengewindes kann über einen Messtaster am Antastzylinder (ø d2) geprüft werden • Die Prüfung des Innengewindes auf Lehrenhaltigkeit erfolgt mit herkömmlichen Gewinde-Lehrdornen (siehe Seite 546 - 547) Characteristics of the tapered plug gauge for checking radial run-out: • Run-out accuracy of the contact cylinder (ø d2) towards major diameter of thread (ø d1) less than 0.01 mm • Pitch diameter of the thread plug gauge go at third thread (3xP) ➞ sufficient lead in the thread • Pitch diameter of the thread plug gauge go/no-go at the second to the last thread (l2 –1xP) ➞ clamping of the check plug gauge • The major diameter of the thread is cylindrically made to fit the thread plug gauge go to guarantee that the check plug gauge jams in the pitch diameter and not in the major diameter Handling of the tapered thread plug gauge for checking radial run-out: • The check plug gauge is manually screwed into the internal screw until properly tightened • Thanks to the light taper shape in the pitch diameter along the entire length of the thread (l2) , the axis of the check plug gauge is centred with the axis of the internal thread • The coaxiality of the internal thread can be checked with a measuring probe at the contact cylinder (ø d2) • The internal thread can be checked for true-to gauge accuracy with conventional thread plug gauges (see pages 546 - 547)
RkJQdWJsaXNoZXIy NjMxNTU=